XCD RFD Transmitter with 3/4 in. NPT entry, 316SS

$1,597.00

Description

Sensepoint XCD RFD Transmitter with 3/4 in. NPT entry, 316SS

The Honeywell Sensepoint XCD RFD is a remote flammable detection system for LEL monitoring applications. The XCD RFD combines the XCD transmitter with the 705 combustible Sensor, and is certified for use in Class IDiv.1 rated areas. The XCD RFD offers one man, non-intrusive, operation and reduces routine maintenance time and costs. The XCD transmitter includes two programmable alarm/fault relays as well as an industry standard 4-20mA output, with optional Modbus RTU. Calibration and relay operation of the transmitter may be adjusted via the transmitters’ backlit LCD. Outputs are automatically inhibited during adjustment thereby reducing the risk of false alarm at the control panel during maintenance. XCD RFD is supplied with all necessary accessories for easy installation. It can be mounted on a wall or 2" round support pole using the universal bracket provided. The detector is ideal for use with either conduit or steel wire armored cable and glands and includes both 3/4" NPT and M20 entries to the junction box.
High Value Sensing Technology • Poison-resistant catalytic bead sensors offer reliable, long-lasting sensing life in an explosion-proof assembly • Low power consumption, reducing cost of ownership • Accurate detection with fast response Easy-Mount Utility • Mount transmitter in easy to access area even if sensor is located in difficult or restricted access area • Mount sensor up to 100 feet from transmitter • Mounting hardware available for pipe, duct and junction box installations Easy to Use • Easy to read tri-color backlit display with digits, bar graph and icons • Fully configurable via non-intrusive magnetic switches • Selectable sink or source 4-20mA output • Auto-inhibit during maintenance prevents false alarms Cost Effective • Common transmitter platform: monitor full range of flammable gases • Longer sensor life compared to electrochemical sensors • Simple operation cuts training costs • Reduced spares and stock costs • Non-intrusive, one-man operation reduces maintenance cost • Optional Modbus adds diagnostic capabilities and advanced intelligence to further reduce costs
• Oil & Gas • Petrochemical • Mechanical Rooms • Warehouses • Bus terminals • Loading docks • Fume hoods • Gas storage • Digesters • H2S scrubbers • Pumps • Coal silos • Turbines • Compressors
Use3-wire, 4-20mA, transmitter with optional Modbus for use with remotely mounted flammable gas sensors 705 and 705HT
Electrical
Input Voltage Range16 to 32VDC (24VDC nominal)
Max Power ConsumptionMax 5 Watts. at 24Vdc (see section 2 regarding maximum in rush current)
Current Output4-20mA (Source or Sink)
≥0.0<1.0 mA: Fault
4.0 mA to 20.0 mA: Inhibit (during configuration/user settings)
22.0 mA: Maximum over range
Terminals15 x screw terminals suitable for wire diameter 0.5mm2 to 2.5mm 2 (20AWG to 13AWG)
Relays3 x 5A@250VAC. Selectable normally open or normally closed (switch) and energized/de-energized (programmable)
CommunicationRS485, Modbus RTU
Construction
MaterialEpoxy painted aluminum alloy or 316 Stainless Steel
Weight (approx.)Aluminum Alloy LM25: 4.4lbs
316 Stainless Steel: 11lbs
MountingPole or wall mounting
Cable Entries2 x ¾” NPT
Sensor Entries¾” NPT
Environmental
IP RatingIP66 in accordance with EN60529:1992, NEMA 4X (Tested by third party laboratory)
Operating Temperature-40ºF to +149ºF (-40ºC to +65ºC)
Operating HumidityContinuous 20-90% RH (non condensing), Intermittent 10-99% RH (non condensing)
Operating Pressure90-110kPa
Storage Conditions-13°F to +149°F (-25°C to +65°C)
Certification
UScCSAus approved for Class I, Division 1, Groups B, C & D Hazardous Locations. Performance approved to the following standards; ANSI/ISA-12.13.01
CanadacCSAus approved for Class I, Division 1, Groups B, C & D Hazardous Locations. Performance approved to the following standards;
C22.2 No. 152-M1984
PerformanceC22.2-152, ANSI/ISA 121301

Additional information

Weight 11 lbs